Cartridge pleating is a method of gathering large amounts of fabric to a small waistband or shoulder armscye without adding bulk to the seam. It also makes the fabric spring away from the waist or shoulder more than normal box-pleating, knife-pleating or gathering does. It was fashionable for gathering large sleeves to the shoulder on men's clothing during the 15th century, and was also a popular method during the 16th century for attaching full skirts to waistbands and bodices.
Cartridge pleating must be sewn by hand, but in many cases is worth the effort. When creating an Elizabethan gown with a heavy skirt, it adds to the period silhouette; in some cases, the "spring" caused by cartridge pleating can eliminate the need for a bumroll under the skirt to hold the fabric out from the hips.
If you've never cartridge pleated anything before and plan to do it for a skirt or sleeve, it's a good idea to take a length of the fabric you'll be using and pleat it, using the following instructions, before pleating the skirt or sleeve itself. This way you can work out the optimum stitch size, gathering tightness, etc. for this particular fabric.
First, take the edge of your skirt which you plan to attach to a waistband and fold over the edge to the inside 2 to 3 inches. If the skirt fabric is a relatively thin one, you can add a strip of wool, flannel, velvet, or other thick fabric inside this fold to give the pleats more body.Using a strong thread (I use a silk buttonhole twist), sew a largish running stitch half an inch away from the folded edge of the fabric. Leave a length of thread free at the beginning and end of the stitch. Repeat this running stitch half an inch further away from the edge, making sure that the thread goes in and out of the fabric at the same places as your first row of stitching did. Leave lengths of thread free at the beginning and ends of this row, as you did the first one. Once again, move 1/2 an
inch further away from the edge and do another row, matching the ins and outs of the above two rows of stitches.The size of the stitches depends on the thickness and body of the fabric you're pleating. If you're using a heavy upholstery velvet, the stitches can be half an inch to 1 inch wide. If you're using a brocade or other thinner fabric, make the stitches 1/4 to 1/2 inch wide. Experiment a little, if possible, before starting on the actual clothing item.Knot the three threads together at each end. Then begin pulling on the threads at one end, gathering the fabric as you go. It should accordion together into deep pleats. (see picture to the right) Ideally, you should gather the fabric tightly enough so that it doesn't slide back and forth, but not so tightly that there's a lot of tension on the threads. Once you've gathered the fabric, and measured it to see that it fits the waist, knot the threads you used to gather the pleats together so that they stay properly gathered.
Sew the pleats to the waistband. Instead of sewing the waistband and the edge of the fabric together as you do with normal pleats, with cartridge pleats, you whipstitch the gathered edge of your fabric to a finished waistband, armscye or other seam edge. Lay the outside of the waistband/whatever against the outside of the pleats, with the waist edge matching the edge of the cartridge-pleated fabric. Using a strong thread, stitch the waistband to the top of each pleat with two or three stitches. The finished product should resemble the picture below.
For the doll maker miniaturist I have found that if you use the 1" or 1/2" pretty pleater board it makes nice cartridge pleats. Since the cartridge pleat is kind of a big pleat the 1" seems like the right scale for ladies. You can see my article on pleaters here: http://creativedoll.blogspot.com/2008/01/pleaters.html
Michelle
Michelle
Leed, Drea, A Short Tutorial on Cartridge Pleating a Skirt] ©2000 Dayton, OH: Author. Retrieved [8/16/08] from the World Wide Web: elizabethancostume.net
1 comment:
Thanks a million, Michelle. I'll give this a try and report back.
Brad
Post a Comment